P0106 — MAP/BARO Sensor Range/Performance

OBD-II diagnostic trouble code reference.

P0106 is an OBD-II diagnostic trouble code defined under SAE J2012 — the standard governing fault-code reporting on light- and medium-duty vehicles since 1996. Manifold Absolute Pressure sensor signal is outside expected range for current engine load The fault sits in the engine system, so the typical service path is targeted inspection of that subsystem before broader troubleshooting. This page summarizes what P0106 means in plain English, common causes when documented, the standard 5-step diagnostic flow, and any FMCSA roadside-inspection violations that cite this code.

Code:
P0106
System:
OBD-II
Category:
engine
Severity:
Moderate severity

Severity classification

P0106 is classified as Moderate severity (moderate).

Meaning

What this fault code indicates.

Manifold Absolute Pressure sensor signal is outside expected range for current engine load

Typical Symptoms

Driver-observable indications commonly associated with this code.

  • rough idle
  • poor acceleration
  • stalling
  • surging

Related Codes

Codes commonly diagnosed alongside this one or sharing the same code family.

How to diagnose P0106

  1. Confirm the code is current, not historical. Use a scan tool to read both Active and Historical (or Inactive / Logged) codes. P0106 matters most when it appears in the Active list. Historical-only codes can reflect a one-off event that has already cleared.
  2. Note any other codes set at the same time. Pull the full list of codes the ECM is reporting and write down which ones share a Freeze Frame timestamp with P0106. A simultaneous failure pattern often points to the root cause faster than any single code in isolation.
  3. Check the most-common cause for this code. Before replacing parts, check the most-common cause for this code (start with the simplest root causes — wiring, connector corrosion, sensor failure — before replacing larger components). The "Common causes" panel on this page lists the established root causes when we have published data — when it is empty, fall back to the OEM service manual or a licensed diagnostic database.
  4. Inspect the relevant component. Physically inspect the engine subsystem: connector pins, wiring harness, ground straps, and sensor body for damage, corrosion, or contamination. Many DTCs are wiring or connector faults rather than failed components.
  5. If unsure, take to a qualified diagnostic technician. If the code returns after repair, or if the actual fault is not obvious from the inspection, escalate to a shop with the proper licensed scan tool for the vehicle (heavy-duty trucks need a J1939-aware tool, not a generic OBD-II reader). Replacing parts based on the code alone is the most common cause of repeat repair costs.

Frequently asked questions about P0106

What does P0106 mean?
P0106 (MAP/BARO Sensor Range/Performance) — Manifold Absolute Pressure sensor signal is outside expected range for current engine load
Is P0106 a serious problem?
P0106 is classified as moderate severity (Moderate severity). It is not typically an immediate-stop condition, but should be diagnosed before the next major trip or inspection.
Can I drive with P0106 active?
Whether you can drive with P0106 active depends on the specific failure mode and vehicle. As a general rule, if there is no immediate drivability issue and no warning lamp other than the MIL, the vehicle is usually drivable to a service location. We don't have a definitive driveability determination on file for P0106.
What's the typical cost to fix P0106?
We don't have public cost data on this for P0106. Repair cost depends heavily on the actual root cause (which the code itself does not specify), the vehicle make and model, and labor rates in your area. Get a diagnostic charge quote from a shop that has the proper scan tool for the vehicle before authorizing any parts replacement.
Will P0106 cause an emissions failure?
P0106 is not in the standard set of emissions monitors. By itself it should not cause an emissions test failure, but the underlying fault may. We don't have a definitive emissions-impact classification on file for P0106.
How is P0106 different from related codes?
P0106 sits in the same family as P0107, P0108, P0109. They share a common system or component, but each identifies a distinct failure mode or location. The "Related Codes" panel above lists every sibling we have on file so you can compare meanings side-by-side.
Where can I find the official spec for P0106?
OBD-II codes are defined under SAE J2012, which is a paid standard published by SAE International. The full canonical text is available through SAE's Digital Annex (www.sae.org/standards/content/j2012/) or licensed scan-tool databases (Mitchell, Alldata, Identifix). We don't republish the licensed text here — the description above is a plain-English summary.
What inspection violations might cite P0106?
We don't have any FMCSA roadside-inspection violations on record that cite P0106 directly. Most inspection violations reference FMCSR sections (49 CFR 393.x, 396.x) rather than DTCs — but if an inspector finds an active emissions, brake, or lighting code, they may note it as evidence supporting an OOS order.

Related pages

Data sources & freshness

TruckCodex aggregates official public-sector datasets. See the Source registry for dataset-level coverage and the Freshness log for last-import timestamps.

Census, SAFER, SMS, Licensing & Insurance (L&I), roadside inspections, crashes, and authority history.

Refreshed daily.

Vehicle recall campaigns, defect investigations, and consumer safety complaints (SCRS).

Refreshed daily.
EIA

Retail diesel and gasoline price history and state fuel-tax tables.

Refreshed weekly.

Cross-border carrier registry and Canadian recall campaigns where applicable.

Refreshed weekly.

TruckCodex is an independent aggregator; it is not affiliated with FMCSA, NHTSA, EIA, or Transport Canada. Always verify compliance-critical information directly with the originating agency.